0

Camshafts & Valvetrain

Are your valves starting to float at high revs, or does your engine need a new camshaft with more lift? This category brings together the parts of the valvetrain: camshafts, valves, springs, retainers, valve locks, rocker arms, lifters, pushrods and timing components. It is for you if you are rebuilding a cylinder head or building a project for higher revs.

What the valvetrain does

The camshaft controls when and how far the valves open, and therefore how the engine draws in air and pushes out exhaust gas. Depending on the engine design, the motion is transferred via lifters, cam followers, rocker arms or pushrods, while the valve springs close the valve again. Retainers and valve locks hold the spring in place on the valve stem. Valve guides and valve stem seals ensure that the valve moves precisely and does not draw oil down into the combustion chamber.

How to choose a camshaft and springs

A camshaft with more lift and longer duration can move power higher up the rev range. However, the result depends on the engine's other specifications, such as compression, cylinder head, intake and whether the engine runs boost. When lift is increased, the valve springs typically need to be matched. Too little spring pressure can cause valve float, while too much can increase wear on the cam and lifters. Also check that the spring does not coil bind at full lift and that there is clearance between valve and piston.

  • Lift and duration in relation to the desired rev range
  • Spring pressure, installed height and the spring's maximum lift
  • Retainer material, e.g. steel or titanium, based on revs and use
  • Fitment to engine code, valve stem diameter and spring seats

Kits and adjustable cam gears

Springs, retainers and seats can be bought individually or as kits where the parts are matched to each other. In this category you will find, for example, kits with dual springs, retainers and spring seats from Brian Crower and beehive spring kits with steel retainers from COMP Cams. Other brands in the category include Ferrea, Supertech and GSC Power Division. Adjustable cam gears among the timing components make it possible to fine-tune the camshaft's timing relative to the crankshaft. This typically requires careful degreeing and may require adjustments to the engine management.

Installation and maintenance

Working on the valvetrain requires precise tools and the manufacturer's specifications. Valve clearance must be checked and adjusted after installation. On some engines this is done with valve caps or shims. New camshafts and lifters often require a break-in procedure and the right lubrication, so follow the instructions for the specific product. If your project also includes pistons or other parts, you will find them under engines and components.

Frequently asked questions

Do I need to replace the valve springs when I install a new camshaft?

Often yes, especially if lift or revs are increased. The springs must suit the cam's lift and profile so the valve closes correctly without the spring coil binding. Check the manufacturer's recommendation for the specific camshaft.

What is the difference between steel and titanium retainers?

Titanium retainers typically weigh less, which can reduce the moving mass in the valvetrain. The choice depends on revs, spring pressure and the manufacturer's recommendation for your particular engine.

Why does valve clearance need to be checked after installation?

Too little clearance can prevent the valve from closing fully, while too much can cause noise and extra wear. After replacing the camshaft, valves or lifters, the clearance should therefore be measured and adjusted to specification.

Can a new camshaft affect inspection and road approval?

The parts sit inside the engine, but a changed cam profile and timing can affect emissions and noise. Whether the car can be approved depends on the product and the car, so check the requirements for the specific part number before modifying the engine.

View as Grid List
Sort by
Display per page

Valve Steel Exh Honda XR/TRX 400

wisVES003
Wiseco Honda XR/TRX 400 Steel Exhaust Valve
56,79 € excl. VAT

Valve Steel Int Honda XR/TRX 400

wisVIS003
Wiseco Honda XR/TRX 400 Steel Intake Valve
42,79 € excl. VAT

Valve Stem Seal Set

felSS72917
Fel-Pro 06-15 Mazda MX-5 Miata/15-21 Ford Mustang Engine Valve Stem Oil Seal Set
41,06 € excl. VAT

Valve Stem Seal Set

felSS702832
Fel-Pro 18-22 Acura NSX/07-14 TL/10-14 TSX/08-17 Honda Accord Engine Valve Stem Oil Seal Set
44,75 € excl. VAT

Valve Stem Seal Set

felSS71327
Fel-Pro 18-21 Ford F-150/11-17 Mustang/10-12 Fusion Engine Valve Stem Oil Seal Set
57,43 € excl. VAT

Valve Stem Seal Set

felSS72936
Fel-Pro 11-17 Ford F-150/Mustang 5.0L Engine Valve Stem Oil Seal Set
68,59 € excl. VAT

Valve Stem Seal Set

felSS72910
Fel-Pro 07-20 Toyota Tundra/08-20 Sequoia/08-20 Land Cruiser Engine Valve Stem Oil Seal Set
62,92 € excl. VAT

Valve Stem Seal Set

felSS728783
Fel-Pro 05-14 Toyota Tacoma/03-20 4Runner Engine Valve Stem Oil Seal Set
48,26 € excl. VAT

Valve Stem Seal Set

felSS72814
Fel-Pro 13-14 Subaru WRX/13-20 WRX STI/00-12 Outback Engine Valve Stem Oil Seal Set
32,99 € excl. VAT

Valve Stem Seal Set

felSS729331
Fel-Pro 15-20 Subaru WRX/16-20 BRZ/13-16 Scion FR-S//17-20 Toyota 86 Engine Valve Stem Oil Seal Set
55,30 € excl. VAT

Valve Stem Seal Set

felSS72802
Fel-Pro 94-05 Mazda Miata/93-97 MX-6 Engine Valve Stem Oil Seal Set
57,70 € excl. VAT

Valve Stem Seal Set

felSS70537
Fel-Pro Dodge D150 SS 70537 Engine Valve Stem Oil Seal Set
21,60 € excl. VAT